英语翻译2.-1This is the analog supply pin for the ADCsand other

英语翻译
2.-1
This is the analog supply pin for the ADCsand other analog circuits in the XADC.It can be tied to the 1.8V VCCAUX supplyhowever in a mixed-signal system the supply should be connected to a separate1.8V analog if available.See Analog Power Supply and Ground (VCCADC andGNDADC),page 69 for more information.This pin should never be tied to GND.The pin should be tied to VCCAUX even if the XADC is not being used.
This is the ground reference pin for theADCs and other analog circuits in the XADC.It can be tied to the system groundvia an isolating ferrite bead as shown in Figure 1-2.In a mixed-signal systemthis pin should be tied to an analog ground plane if available,in which casethe ferrite bean is not required.See Analog Power Supply and Ground (VCCADCand GNDADC),page 69 for
more information.This pin should always betied to GND even if the XADC is not being used.
2-2
This pin should be tied to an external1.25V accurate reference IC (±0.2%) for best performance of the ADCs.It shouldbe treated as an analog signal that together with the VREFN signal provides adifferential 1.25V voltage.By connecting this pin to GNDADC (see Figure 1-2)an on-chip reference source (±1%) is activated.This pin should always beconnected to GNDADC if an external reference is not supplied.See Reference Inputs(VREFP and VREFN),page 69 for more information.
This pin should be tied to GND pin of anexternal 1.25V accurate reference IC (±0.2%) for best performance of the ADCs.It should be treated as an analog signal that together with the VREFPsignalprovides a differential 1.25V voltage.This pin should always be connected toGND even if an external reference is not supplied.See Reference Inputs (VREFPand VREFN),page 69 for more information.

这是模拟电源引脚在XADC的ADCsand其它模拟电路.它可连接到1.8V VCCAUX supplyhowever在混合信号系统的电源应连接到一个separate1.8V模拟,如果available.See模拟电源和接地（VCCADC andGNDADC）,有关详细信息,第69页.该引脚不应该绑GND.The引脚应接,即使不被使用的XADC到VCCAUX.
这是接地参考引脚theADCs和其它模拟电路中的XADC.它可连接到系统groundvia一个隔离铁氧体磁珠,如图1-2所示.在混合信号systemthis引脚应该连接到模拟地平面（如果可用）,其中casethe不要求铁氧体豆.看到模拟电源和接地（VCCADCand GNDADC）,69页
更多信息.该引脚应始终betied到GND即使不被使用的XADC.
2-2
该引脚应为ADC的最佳性能连接到一个external1.25V准确的参考IC（±0.2％）.那么只能视为与该VREFN信号一起提供adifferential 1.25V电压的模拟信号.通过此引脚连接到GNDADC（见图1-2）片上基准源（±1％）被激活.该引脚应始终beconnected如果不提供一个外部参考GNDADC.请参阅参考输入（VREFP和VREFN）,第69页了解更多信息.
该引脚应连接到anexternal 1.25V准确的参考IC的GND引脚（±0.2％）为ADCs.It的最佳性能应该是T 请参阅参考输入（VREFPand VREFN）,了解更多信息第69页 .
再问： 要通顺点的啊，不要机器翻得~~