神马作文网英语翻译1 Fillet show 2 Draft is 5 DEG maximum per side,draft fo
来源：学生作业帮 编辑：神马作文网作业帮 分类：英语作业 时间：2024/11/06 18:26:31
英语翻译
1 Fillet show
2 Draft is 5 DEG maximum per side,draft for round holes and bosses IEG maximum include angle .
3 Tool number are to be 003-005 raised,150 high simple gothic characters located as specified
4 Special surface appearance requirements as indicated by a leader and the finish designation(1) finish a vapor hone all exterior surfaces (2)finish B
5 Tunnel “ or sub gate acceptable
6 Recessed gate acceptable of below surface 0.015 maximum
7 Eject
8 Ejector pin marks
9 Pin marks acceptable to 0.000 raised ,0.015 depressed
10 Pin mark flash must be removed
11 In addition ,UL recognized molders must provide their UL assigned code designation with above information
12 This part mate with part from tool number xxxx and xxxx and shall be progressed to a satisfactory fit as determined by engineering dept
1 Fillet show
2 Draft is 5 DEG maximum per side,draft for round holes and bosses IEG maximum include angle .
3 Tool number are to be 003-005 raised,150 high simple gothic characters located as specified
4 Special surface appearance requirements as indicated by a leader and the finish designation(1) finish a vapor hone all exterior surfaces (2)finish B
5 Tunnel “ or sub gate acceptable
6 Recessed gate acceptable of below surface 0.015 maximum
7 Eject
8 Ejector pin marks
9 Pin marks acceptable to 0.000 raised ,0.015 depressed
10 Pin mark flash must be removed
11 In addition ,UL recognized molders must provide their UL assigned code designation with above information
12 This part mate with part from tool number xxxx and xxxx and shall be progressed to a satisfactory fit as determined by engineering dept
1 Fillet show
焊角标示
2 Draft is 5 DEG maximum per side,draft for round holes and bosses IEG maximum include
angle .
圆孔和凸台IEG标准最大包含角度每边最大5度
3 Tool number are to be 003-005 raised,150 high simple gothic characters located as
specified
刀具编号,应高出3－5,高度150,simple gothic（哥特式）字体
4 Special surface appearance requirements as indicated by a leader and the finish
designation(1) finish a vapor hone all exterior surfaces (2)finish B
特定表面外观要求需用引出线标示并标注完成说明 （1）外表面水磨 （2） 完成等级B
5 Tunnel “ or sub gate acceptable
允许暗孔和暗浇口
6 Recessed gate acceptable of below surface 0.015 maximum
最多低于表面0.015的凹浇口
7 Eject
成型
8 Ejector pin marks
标注推板
9 Pin marks acceptable to 0.000 raised ,0.015 depressed
针标范围＋0.000-0.015
10 Pin mark flash must be removed
清楚针标毛边
11 In addition ,UL recognized molders must provide their UL assigned code designation
with above information
另外,UL认证制模工必须提供UL认证牌号
12 This part mate with part from tool number xxxx and xxxx and shall be progressed to a
satisfactory fit as determined by engineering dept
这部分适用刀具编号为xxxx和xxxx,也可根据技术部门的决定进一步使用范围.
焊角标示
2 Draft is 5 DEG maximum per side,draft for round holes and bosses IEG maximum include
angle .
圆孔和凸台IEG标准最大包含角度每边最大5度
3 Tool number are to be 003-005 raised,150 high simple gothic characters located as
specified
刀具编号,应高出3－5,高度150,simple gothic（哥特式）字体
4 Special surface appearance requirements as indicated by a leader and the finish
designation(1) finish a vapor hone all exterior surfaces (2)finish B
特定表面外观要求需用引出线标示并标注完成说明 （1）外表面水磨 （2） 完成等级B
5 Tunnel “ or sub gate acceptable
允许暗孔和暗浇口
6 Recessed gate acceptable of below surface 0.015 maximum
最多低于表面0.015的凹浇口
7 Eject
成型
8 Ejector pin marks
标注推板
9 Pin marks acceptable to 0.000 raised ,0.015 depressed
针标范围＋0.000-0.015
10 Pin mark flash must be removed
清楚针标毛边
11 In addition ,UL recognized molders must provide their UL assigned code designation
with above information
另外,UL认证制模工必须提供UL认证牌号
12 This part mate with part from tool number xxxx and xxxx and shall be progressed to a
satisfactory fit as determined by engineering dept
这部分适用刀具编号为xxxx和xxxx,也可根据技术部门的决定进一步使用范围.
Draft
英语翻译Remember that your initial draft is only that.
英语翻译Hi guys,Attachment is the quotation draft of Lyondellbas
英语翻译Please find as below draft of Standby L/C,in order to fo
英语翻译1 union-wide commitment to increast its pledge 2 draft p
DEMAND DRAFT
英语翻译The buyer is to accept the documentary draft xx days aft
英语翻译Payment is to be made against draft drawn under confimed
英语翻译8.Remittance by banker’s demand draft is often referred
英语翻译Today is Sat,will arrange the SBLC draft for your banker
英语翻译DWT summer 33717.10mt on draft 9.82m 尤其是这个 on draft
英语翻译1,BENEFICIARY'S DRAFT IN DUPLICATE AT SIGHT FOR 100PCT C