神马作文网美国机械图纸中标注1/4 DRILL 3.5 DEEP TO DRILL POINT 1/16-27 N.P.T
来源：学生作业帮 编辑：神马作文网作业帮 分类：英语作业 时间：2024/11/10 20:49:21
美国机械图纸中标注1/4 DRILL 3.5 DEEP TO DRILL POINT 1/16-27 N.P.T
美国机械图纸中标注: 请大侠帮忙解释是什么意思?谢谢!
1） 1/4 DRILL 3.5 DEEP TO DRILL POINT 1/16-27 N.P.T.("A”side only) ONE HOLE (grease POP-out for slug)是什么意思?
2）DRILL THRU &C'BORE FOR 3/8 S.H.C.S-8 HOLES.
3)5/16 DIAMETER FULL ROUND RUNNER
4)3/16 DIA END MILL AIR SLOT .13 DEEP
5）use 1/8 DIA BAL NOSE CUTTER .06 DEEP
6)3/32 DRUKK .25 DEEP ON A 30º ANGLE AS SHOWN - 2 HOLES IN B HALF ONLY.
7）USE SOLID MODEL FOR THREADED AREA 2 1/2-12（UN）.
8）DRILL THRU .81 DIA DIRECT BOLT -10 HOLES
9)DRILL THRU 1.00 DIA WIRE HOLE -2 HOLES
10)DRILL CLEARNCE FOR 3/8 EJ. PINS -9 HOLES
11)DRILL & TAP FOR 5/8-11 LIFT STRAP -2 HOLES
12)DRILL THRU .75 DIA KILL SWITCH ROD CLEARNCE - ONE HOLE
13)DRILL .750 DIAMETER (FLAT BOTTOM EJ. SPRING -4 HOLES
请大家帮帮忙吧,谢谢!
美国机械图纸中标注: 请大侠帮忙解释是什么意思?谢谢!
1） 1/4 DRILL 3.5 DEEP TO DRILL POINT 1/16-27 N.P.T.("A”side only) ONE HOLE (grease POP-out for slug)是什么意思?
2）DRILL THRU &C'BORE FOR 3/8 S.H.C.S-8 HOLES.
3)5/16 DIAMETER FULL ROUND RUNNER
4)3/16 DIA END MILL AIR SLOT .13 DEEP
5）use 1/8 DIA BAL NOSE CUTTER .06 DEEP
6)3/32 DRUKK .25 DEEP ON A 30º ANGLE AS SHOWN - 2 HOLES IN B HALF ONLY.
7）USE SOLID MODEL FOR THREADED AREA 2 1/2-12（UN）.
8）DRILL THRU .81 DIA DIRECT BOLT -10 HOLES
9)DRILL THRU 1.00 DIA WIRE HOLE -2 HOLES
10)DRILL CLEARNCE FOR 3/8 EJ. PINS -9 HOLES
11)DRILL & TAP FOR 5/8-11 LIFT STRAP -2 HOLES
12)DRILL THRU .75 DIA KILL SWITCH ROD CLEARNCE - ONE HOLE
13)DRILL .750 DIAMETER (FLAT BOTTOM EJ. SPRING -4 HOLES
请大家帮帮忙吧,谢谢!
1 / 4的钻头）3.5深钻点1/16-27“不扩散核武器条约”（“一”方只）一杆进洞（油脂蛞蝓的POP）2）3 / 8内六角8孔钻透C'BORE.
3）饱满圆润转轮直径5 / 16
4）3 / 16直径立铣刀空气槽0.13深
5）使用1 / 8直径0.06深BAL头铣刀
6）3 / 32 DRUKK,0.25深在30度角,如图所示 - 2孔乙半只.
7）使用螺纹面积2 1/2-12（UN）的实体模型.
8）0.81直径直接螺栓-10孔钻透
9）1.00 -2直径线孔孔钻透
10）3 / 8 EJ钻CLEARNCE.骏-9孔
11）钻孔和挖掘5/8-11升降带-2孔
12）钻透0.75直径的KILL开关杆CLEARNCE - 一杆进洞
13）0.750直径（平底EJ春季-4孔钻
3）饱满圆润转轮直径5 / 16
4）3 / 16直径立铣刀空气槽0.13深
5）使用1 / 8直径0.06深BAL头铣刀
6）3 / 32 DRUKK,0.25深在30度角,如图所示 - 2孔乙半只.
7）使用螺纹面积2 1/2-12（UN）的实体模型.
8）0.81直径直接螺栓-10孔钻透
9）1.00 -2直径线孔孔钻透
10）3 / 8 EJ钻CLEARNCE.骏-9孔
11）钻孔和挖掘5/8-11升降带-2孔
12）钻透0.75直径的KILL开关杆CLEARNCE - 一杆进洞
13）0.750直径（平底EJ春季-4孔钻
美国机械图纸中标注1/4 DRILL 3.5 DEEP TO DRILL POINT 1/16-27 N.P.T
机械图纸中 drill thru with the letter
图纸上标注drill & tap for 3/8-16 4 places.
英文图纸中Drill&Tap 8-32x.375 deep的意思,换算成公制应该怎么表达
英语翻译1-NEW drill pipe acc.To API and RP7G 5" O.D nominal size
what is the size of a drill bit that is 1/16 of a
drill thru #7(.201dia) ＆tap 1/4-20NC(2HOLES)是什么意思?
drill是什么意思?
DRILL怎么样
drill是什么意思
tap drill
机械图纸标注中直径前面加P.C或是P.C.