神马作文网英语翻译Blow molding is the third largest plastics processing te
来源：学生作业帮 编辑：神马作文网作业帮 分类：英语作业 时间：2024/11/20 22:58:22
英语翻译
Blow molding is the third largest plastics processing technique worldwide and is generally recognized to be one of the fastest growing areas in the plastics industry[1].One of the essential steps which constitutes the blow molding cycle is the inflation of the parison.The entire process of parison inflation occurs in two successive stages,namely,free inflation followed by confined inflation.The parison inflation process is highly complex,involving the interaction of several process variables,such as the inflation pressure,material characteristics,parison thickness distribution,and parison temperature profile.
There have been quite a few reports in the existing literaturre on the simulation of parison inflation[2--9].Ryan and Dutta[3] made an analytical treatment of the free inflation of a viscoelastic parison by assuming a one-dimensional isothermal deformation.This simplified analyses cannot be used to predict realistic shapes of the parison during its inflation.
The finite element method (FEM) has been used to simulate the inflation of parison over the last decade[4--9].However,modeling blow molding inflation process with the FEM requires that many of the most difficult aspects of the FEM be addtessed in the analysis.These difficulties arise because of large strains,large deformations,nonlinear material behavior and so on during the inflation of parison.
In this paper,a mathematical model has been derived for simulating the parison free inflation in the plastics extrusion blow molding.In order to evaluate the predictive capabilities of the model,the instantaneous images of parison inflation within a mold epuipped with glass side windowa have been obtained by using a video capture technique.
1 Theoretical Analysis
Consider the free inflation of an isotropic and incompressible annular parison with an uniform radius and thickness,and length 2L in the initial state,as shown in Fig.1.The parison is assumed to be treated as a membrane (with thickness much less than any radius of curvature) so that any change in the deformation variables across the thickness may be neglected.Gravity and surface tension effects are neglected.Cylindrical polar coordinate system(r,r,x) is taken and all puantities are independent of r because of symmetry.Amaterial particle that locates at (r,r,x) during inflation is originally at (r,r,x).The ends of the parison are at x=0 and x=2L,and there is symmetry about the plane x=L.
Blow molding is the third largest plastics processing technique worldwide and is generally recognized to be one of the fastest growing areas in the plastics industry[1].One of the essential steps which constitutes the blow molding cycle is the inflation of the parison.The entire process of parison inflation occurs in two successive stages,namely,free inflation followed by confined inflation.The parison inflation process is highly complex,involving the interaction of several process variables,such as the inflation pressure,material characteristics,parison thickness distribution,and parison temperature profile.
There have been quite a few reports in the existing literaturre on the simulation of parison inflation[2--9].Ryan and Dutta[3] made an analytical treatment of the free inflation of a viscoelastic parison by assuming a one-dimensional isothermal deformation.This simplified analyses cannot be used to predict realistic shapes of the parison during its inflation.
The finite element method (FEM) has been used to simulate the inflation of parison over the last decade[4--9].However,modeling blow molding inflation process with the FEM requires that many of the most difficult aspects of the FEM be addtessed in the analysis.These difficulties arise because of large strains,large deformations,nonlinear material behavior and so on during the inflation of parison.
In this paper,a mathematical model has been derived for simulating the parison free inflation in the plastics extrusion blow molding.In order to evaluate the predictive capabilities of the model,the instantaneous images of parison inflation within a mold epuipped with glass side windowa have been obtained by using a video capture technique.
1 Theoretical Analysis
Consider the free inflation of an isotropic and incompressible annular parison with an uniform radius and thickness,and length 2L in the initial state,as shown in Fig.1.The parison is assumed to be treated as a membrane (with thickness much less than any radius of curvature) so that any change in the deformation variables across the thickness may be neglected.Gravity and surface tension effects are neglected.Cylindrical polar coordinate system(r,r,x) is taken and all puantities are independent of r because of symmetry.Amaterial particle that locates at (r,r,x) during inflation is originally at (r,r,x).The ends of the parison are at x=0 and x=2L,and there is symmetry about the plane x=L.
铸造打击并且一般地被认出是塑料工业[构成铸造周期的打击的十分重要的步骤的1].One是parison的通货膨胀.中的最快的日益增长区域之一在世界范围处理技术的第三大塑料parison通货膨胀的整个的过程在两个连续的阶段中发...
英语翻译Hong Kong is the third largest financial center that nex
英语翻译The injection molding of micro-structures is apromising
英语翻译用这些次回答 The third largest,china,country,be,in the world,i
china is a third largest city in area in the world.
France is Europe’s third largest country and faces the Unite
英语翻译The plastic injection molding is a complex and highly ef
blow molding with accumulators什么意思
英语翻译with the blow?
英语翻译Thegenus Lactobacillus is the largest and,perhaps,the mo
英语翻译Visiting ShanghaiShanghai is one of the largest cities i
英语翻译Indianapolis is the capital and largest city of Indiana,
英语翻译BRIEF INTRODUCATIONHaier is the world's fourth largest w